Impala Tech - Reply to Topic
Engine General Engine Discussion.

Thread: Looking for the best combo with what i have Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Impala Tech forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
02-08-2020 01:09 AM
jmiller1119 Big Dave, ive heard of good things AND bad things with Comp thats why i was looking at Lunati as well. I was leaning towards the voodoo 268/276.....or do you think the 262/268 would be better of the 2? I plan to get a stall either way. And yes a tranny cooler is in the works also, its a heavy car And i agree cheap insurance.
02-06-2020 10:32 AM
BA. I think the 268 cam would be a great cam for that setup. I probably wouldn't go much larger unless I was after that bigger 'cam lope' and not worried about losing a little actual power to under the curve. I would say a great torque converter for that would be 2400-2600, given the gears you are running and the RPM range of that cam in that engine.



If you drive it hard, you might also consider a trans-cooler. It's not a necessity, just nice insurance if you run hard against that converter on take-off a lot. (good times!)
02-04-2020 07:58 PM
Big Dave Why change anything?

Are you looking for a poorer idle with less bottom end power. Then add duration and narrow your lobe separation angle even more.

If you want to drive on the street stop looking at drag racing cams (they are only for drag racing which you can not do with a street driven car. Marine cams for a BBC, and my favorite short circle track cams are way better for the street with a SBC than any drag racing cam. You won't be able to race your dyno as it will be down a bit on peak horsepower, but you will raise and broaden your torque curve which you will feel in the seat of your pants.

I had been buying my cams from Lunati before I stopped building motors professionally. Had a run of bad parts from Comp which prompted me to change vendors.

Big Dave
02-04-2020 07:20 PM
jmiller1119 Nobody?
02-03-2020 01:21 PM
jmiller1119
Looking for the best combo with what i have

Hey guys, working on my motor again kind of stumped on a couple things. I have a 355 with rotating assembly(balanced crank, rods,1.560 flat top with vr's,stock deck height) have L31 vortec heads ls6 beehives, comp retainers and seal bosses machined, will be running a shim gasket( if i did the math right ill have 10.1:1 cr)have a dual plane vortec intake and a choice of a 600 edelbrock,650 holley or a 750 holley. Been looking at cams........and looking and looking. Contemplating comps x268h. What other brands are you guys running with good results? 66 Impala 2 dr(3600lbs)TH350, 3.31 geared 12 bolt with 27" tires(will not put stickies on at any time) need cam advice and torque converter recommendations. Will mostly be a weekend cruiser with speeds below 70mph. I dont want to change anything at this point unless absolutely necessary. Thanks guys!

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome